Studio XB-322 Case for GoPro®

Manufacturer Part No: XB-322

The STUDIO XB-322 Case for GoPro® fits 2-3 GoPros® and its accessories. It is compatible with the GoPro® HERO 3, 3+, 4 and 5, and is the most versatile case in the GoPro® lineup.

*In Stock and Ready to Ship*
$125. 00
Designed for use with GoPro® products. GoPro® is a registered trademarks of Woodman Labs, Inc. in the United States and other countries. Cameras & Accessories Not Included With Cases.

GPC Studio XB 322 Case for GoPro® Open Hero Image

  • GPC Studio XB 322 Case for GoPro® Open Hero Image
  • GPC Studio XB 322 Case for GoPro® Open Empty
  • GPC Studio XB 322 Case for GoPro® Front Open Upper Tray
  • GPC Studio XB 322 Case for GoPro® Front Closed
  • GPC Studio XB 322 Case for GoPro® Squeezelatch Closed
  • GPC Studio XB 322 Case for GoPro® Pressurevalve

Car Charger Batteries Batteries Cable/Accessories GoPro® Charger GoPro® Accessories GoPro® Backdoors GoPro® Backdoors GoPro® Remotes GoPro® Remotes GoPro® Remotes GoPro® Remotes GoPro® Remotes GoPro® Cameras GoPro® Cameras GoPro® Cameras GoPro® Cameras GoPro® Cameras GoPro® Cameras

Studio XB-322 Case
for GoPro® Upper

  • Car Charger
  • Batteries
  • Cable/Accessories
  • GoPro® Charger
  • GoPro® Accessories
  • GoPro® Backdoors
  • GoPro® Remotes
  • GoPro® Cameras
  • SD Cards
Misc./Accessories Misc./Accessories Misc./Accessories Misc./Accessories

Studio XB-322 Case
for GoPro® Lower

  • Misc./Accessories
  • Suction Cup Mounts


  • Water-jet precision cut with closed cell foam to resist water and dust infiltration.
  • Our custom foam is housed in a durable SKB military spec case used by military and industrial leaders.
  • Made in the USA, Shipped Worldwide
  • Padlock holes include stainless steel padlock protector clips
  • Waterproof and dust tight design (MIL-C-4150J)
  • Molded-in hinge for added protection
  • Trigger release latch system
  • Snap-down rubber over-molded cushion grip handle
  • Ambient pressure equalization valve (MIL-STD-648C)
  • Resistant to UV, solvents, corrosion, fungus (MIL-STD-810F)
  • Resistant to impact damage (MIL-STD-810F)
  • Lifetime replacement guarantee
  • Remember! - If it doesn't say GPC in the foam, it isn't guaranteed!


Exterior Length 18in
Exterior Width 14 in
Exterior Depth 7 in



Interior Length 15 in
Interior Width 10.38 in
Interior Depth 6 in



Weight 7 lb 0.00 oz
Shipping Weight 8 lb 0 oz

Related Products

  • GPC UAV GoScope® Extreme-GoPro® Pole 2X Telescoping

    GoScope® Origi...

    The GoScope ® Original-GoPro ® Pole 1X Telescoping is a twice telescoping pole from 21" to 34.5" on all GoPros &...

    $39. 95 $16
    View Now
  • TSA Combination Padlock

    TSA Combination Pa...

    TSA accepted padlocks to provide convenient and secure airport cargo inspection. *In Stock and Ready to Shi...

    $15. 99

    View Now
  • GPC GoScope® Neck Strap

    GoScope® Neck Str...

    The GoScope® Neck Strap allows users to easily store and switch GoPro® buckle attachments. It is compatible with...

    $16. 95 $6
    View Now


The case is bigger than the tool-roll type I purchased previously but still way too small to negate the need for extra containers, especially when travelling overseas. If you have a decent selection of gear, backs, posts, adaptors, mounts, batteries, chargers etc there just is not enough room. I have a gorillapod I would have liked to fit, plus an 18 A-h battery and charger for long time lapses, but not a chance of fitting those in. So, back to the drawing board to see if anyone has actually designed a case which CAN hold ALL of my gear. Alternatively I am going to have to make my own. For users with a smaller collection however I would be quite confident that the case can hold a good range. My fixation with time-lapse is not going to be shared by everyone, so do not let my opinions dissuade you from this case. It is well made but just does not meet all of my needs.
- Cliff Ferguson
I had a tiny old pelican case with no foam and a big brown paper grocery bag that I hauled around with all my GoPro gear. I just purchased the Pro XB-322. Ten minutes after I ordered online, I received an email saying my case had shipped. Great customer service. As far as my gear goes, I have 2 GoPro cameras and a "heaping load" of accessories. This case fits everything (except my Steadicam Smoothee and GoPole) and has a nice lay out via the included foam. My advice, if you are here shopping for a case, go big! I was originally looking a two smaller cases, I'm glad I went with the 322. Spoke to customer service prior to ordering and they were happy to answer my questions and help me pick the right case. I wish I would have bought one a long time ago. Now I can spend more time shooting video and less time rummaging through my grocery bag looking for the right accessory.
- Michael Campbell
Thought I was initially hesitant to spend more than 1/4 the cost of my camera cost for a case, I can assure you that it's a worthy purchase if you need to stay organized and want to ensure safety of your gear under all circumstances. This case has all the right compartments, perfectly shaped for your Go Pro and accessories. The SKB outer shell offers solid latches, water seal and automatic pressure feels like Fort Knox. If you've got the money, I recommend this case.
- Brian M.
I got this case because I have alot of accessories but I only use two to place for strut analysis, most of the time. I almost overlooked this model because I thought it was limited to space for two suction cups and two other cavities. Called and talked to Rick and realized all the pics are possible configurations you can make depending on what you have. I got the case and pulled the perforated foam out of the suction cup cavities and made four nice size ones. It's not the cheap, soft pick and pluck foam,'s just that they made perforations in the foam to be able to make what you want. It's perfect. Thanks for the great design. Highly recommend.
- Craig